- HP MEDIASMART SERVER EX470 SOFTWARE SITE UPGRADE THE STORAGE
- HP MEDIASMART SERVER EX470 SOFTWARE SITE SOFTWARE MUST BE
Hp Mediasmart Server Ex470 Software Site Software Must Be
At the Mac.The Synology has 4 x 4TB drives configured as a RAID 5 array and this stores all our personal and work files and our very large photo archive.Hp Mediasmart Suite Download Software. The sophisticated WHS backup algorithm copies files, folders, and complete images of the PC hard drive.Server Name and Password have to be authenticated prior to using the HP Home Page, or entering preferences for BackUp. This client software must be installed on each PC that you wish to include in the backup operation. Zoftar Software's HP recoveryA: Once you install the MediaSmart Server client software on a PC, it will automatically be backed up to the HP MediaSmart Server.
File Name:HP MediaSmart Photo Software.HP's MediaSmart Servers are basically low-power PCs running Windows Home Server software from a corner of your house. The HP MediaSmart Photo Software enables users to manage and navigate through photos. This package provides the HP MediaSmart Photo Software for supported notebook models that are running a supported operating system.
Hp Mediasmart Server Ex470 Software Site Upgrade The Storage
The connector pinout is shown below.VGA pin connectons to header CN2 ( download PDF).We ordered the correct connector and pins and a short cable was assembled using a screened cable to connect the motherboard to a VGA socket mounted on the back of the machine.The completed VGA connection cable and headerAs access to the motherboard is very restricted we decided to cut an access hole in the side of the case and cut a hole in the rear panel for the new VGA socket. We investigated removing this device and replacing it with a larger capacity chip but we found forum posts from other people who had tried this and resulted in bricking the machine so we keep this in place on the board.We found several blog posts which showed an internal connector which has VGA signals and PS2 ports for keyboards and mouse on the motherboard. We are using around 2TB of photo space at the moment!Ever since we had the direct lightning strike on our home which destroyed all the computers, network devices, TV's, connected household appliances and most of the mains electrical cables which resulted in a complete rewire for the house, we keep disconnected backup devices and off site backups for our critical data.The HP MediaSmart server runs the Windows Home Server operating system and it has a maximum hard drive limit of 2TB per drive which we found after trying to upgrade the storage with new 3TB drives we had spare.After finding that the new larger drives are not supported we researched different ways to use the larger drives and changing the operating system to Linux seemed to be the only way forward.The MediaSmart server is built as a headless machine and doesn’t have any external display ports to allow us to access the BIOS to configure the boot devices so we could boot from a Linux install USB stick to setup the new operating system.The server has an on-board flash storage device with 256MB of space with a simple recovery operating system installed for restoring the Windows Home Server operating system via the network. To keep a duplicate of the most important files we use our older HP MediaSmart EX475 Windows Home machine with 4 x 2TB drives as a secondary backup and we also use removable single drives for a third level of backup with our photos also being backed up to Amazon using our Amazon Prime account which gives unlimited photo storage.
When it came to the setup point were the primary disc is partitioned the setup could not find a disc in the top slot. Anyway I was lead to understand that the uppermost disk was the primary Sata Disc, so after about 30 times of trying to load openmediavault on to the disc with no luck. Then booted the gem up, I was surprised to find the IDE set up in the Cmos consisted of not only the four drives in the bays but, as follows: IDE 0 Master “ “ 0 Slave “ “ 2 Master “ “ 2 Slave “ “ 3 Master “ “3 Slave Plus a 247 MiB USB Disk Serial No AA04012700036216 hiding somewhere in the box.
I then Shut the system down and hoped it would reboot once I had fitted the other 3 Drives (3Tb HDD’s) into the unit. When the install was completed I checked the drives in Openmediavault it showed the 1Tb HDD with the system on it and a USB Disk 247.50MiB disc which I did not mount in Openmediavault. The part of the setup arrived at the HDD format and partitioning and there was the drive, I clicked continue and away it went to complete the install. With the Openmediavault setup disc in a CD Rom connected to the bottom USB socket I did a Cmos save and reboot after the post as the CD Rom started to spin I Hot Shoed the bottom Sata HDD into the bottom slot of the unit. Then I decided to try something new, with a reconfiguration to the boot order I set 1 st boot USB external, 2nd boot HDD and all following boot devices disabled. I then booted the unit with 1Tb Drive in IDE 2 Master and still when it come to the system disc being formatted and portioned no go.
To do this on any HP Media Server it is necessary to have a header cable the upload cannot be done without it unless you like a lot of frustration and hassle. I have yet to upgrade the Memory chips to 4Gb from 2Gb the CPU seems fast enough no stream to the TV or any of the PC, Laptops or Tablets. With Plex plug-in installed I can watch the films and TV recordings on my TV connected to the hard wire network. The system rebooted OK I then configured the 3 x 3TB drives as ext4 File system not a Raid 5 which I wanted to do but I would have lost to much room, I have since backed up all my movies and 20% of my TV Recordings a total of 1.5Tb.
Will keep you updated steveI can't believe what I'm seeing. It is still in the process of being loaded with data and is performing well with access the the filing system from windows desktop works well. The Linux system has updated a few times but not Vista. On the boot into Linux it does show widows Vista in the background but nothing else.
It would halt with some error I can't even remember what it was now. Something happened with the x310 and could not get it to back anything up. The 475 has been in the stock or for a while and up until a couple years ago the 310 was still in use just to back up a couple laptops an a couple desktops. And x310 and an EX475 I think it is.
I'm not too familiar with Linux but I can research and follow instructions. My question to anyone that's still monitoring this is what is should I use to put the old girl back to work as a file server or NAS? Anyone have any ideas. It did so now I'm in the process of making a proper cable. So I took the pinout and an old VGA cable and some breadboard wires and made a temporary VGA cable just to see if it would POST. So I got to investigating and found where people had made the KVM cable.
0 kommentar(er)
